Welded or Woven Wire Mesh in a square pattern defined by the opening size.

Material Selection -

· Aluminum 3003H14	· High-Carbon Steel
· Aluminum 5005H32	· Hot-dipped Galvanized
· Aluminum 5005H34	· Inconel 600
· Aluminum 5052H34	· Monel 400
· Aluminum 6061T6	· Plain Steel
· Brass	· Pre-Galvanized
· Bronze	· Stainless Steel 304
· Copper	· Stainless Steel 304-L
· Electro-Galvanized	· Stainless Steel 316
· Galvannealed	· Stainless Steel 316-L
· Galvanized	· Stainless Steel 409
· Hastelloy C	· Titanium

top

Wire Diameter


Wire diameter is a measure of the thickness of the wires in the wire mesh. When possible, please specify wire diameter in decimal inches rather than in wire gauge.

top

Wire Spacing


Wire spacing is a measure from the center of one wire to the center of the next. If the opening is rectangular, wire spacing will have two dimensions: one for the long side (length) and one for the short side (width) of the opening. For example, wire spacing = 1 inch (length) by 0.4 inch (width) opening. Wire spacing, when expressed as the number of openings per lineal inch, is called mesh.

top

Mesh


Mesh is the number of openings per lineal inch. Mesh is always measured from the centers of the wires. When mesh is greater than one (that is, the openings are greater than 1 inch), mesh is measured in inches. For example, a two-inch (2") mesh is two inches from center to center. Mesh is not the same as opening size. The difference between 2 mesh and 2-inch mesh is illustrated in the examples in the right column.

top

Open Area


Wire Mesh contains open spaces (holes) and material. Open area is the total area of the holes divided by the total area of the cloth and is expressed as a percent. In other words, open area describes how much of the wire mesh is open space. If the wire mesh has 60 percent open area, then 60 percent of the cloth is open space and 40 percent is material.

top

Opening Size


The opening size is measured from the inside edge of one wire to the inside edge of the next wire. For rectangular openings, both an opening length and width is required to define opening size. Differences between opening size and mesh The difference between mesh and opening size is how they are measured. Mesh is measured from the centers of the wires while opening size is the clear opening between the wires. A two mesh cloth and a cloth with 1/2 inch (1/2") openings are similar. However, because mesh includes the wires in its measurement, two mesh cloth has smaller openings than a cloth with an opening size of a 1/2 inch.

top

Rectangular Openings


When specifying rectangular openings, you must specify the opening length, wrctng_opnidth, and the direction of the long way of the opening. Opening Width The opening width is the smallest side of the rectangular opening. In the example to the right, the opening width is 1/2 inch. Opening Length The opening length is the longest side of the rectangular opening. In the example to the right, the opening length is 3/4 inch. Direction of Opening Length Specify whether the opening length (the longest side of the opening) is parallel to the length or width of the sheet or roll. In the example show to the right, the opening length is parallel to the length of the sheet. If direction is not important, indicate “None Specified.”

top

Roll, Sheet, or Cut-to-Size

Wire Mesh comes in rolls, sheets, or the material may be cut to your specifications. The most common roll sizes are 36 or 48 inches x 100 feet: the most common sheet sizes are 36 or 48 inches x 120 inches. You can select from a variety of roll and sheet sizes from the stock list.

Vinylmesh is available in full rolls only.

top

Edge Type


Stock rolls may have salvaged edges. Sheets, panels, and cut-to-size pieces can be specified as “trimmed” or “untrimmed:” Trimmed - The stubs are removed, leaving only 1/16th to 1/8th wires along the edges. In order to produce a trimmed piece, the length and width measurements must be an exact multiple of each sides’ respective wire spacing. Otherwise, when the piece is cut and the stubs are removed, the piece will be smaller than the requested size. Untrimmed, Random Stubs - All stubs along one side of a piece are of equal length. However, the length of stubs on any one side may be different than those on any other side. Stub lengths between multiple pieces may also vary randomly. Untrimmed, Balanced Stubs - The stubs along the length are equal and the stubs along the width are equal; however, the stubs along the length may be shorter or longer than the stubs along the width. Balanced Stubs with Edge Wire - The cloth is cut with untrimmed, balanced stubs. Then, a wire is welded to all sides to produced a trimmed look.

top

Length and Width


Length is the measure of the longest side of the roll, sheet, or cut piece. Width is the measure of the shortest side of the roll, sheet, or cut piece. All cut pieces are subject to shear tolerances.

top

Quantity

Quantity is the number of rolls, sheets or panels, or cut-to-size pieces requested. Unless otherwise specified, the tolerance on quantity is “Exact Quantity". In other words, McNICHOLS will deliver the exact quantity you specify.

top

Matching Existing Wire Mesh

To match existing wire mesh, we recommend that you send us a sample, if you have one, or a drawing. The address and FAX are listed below:

McNICHOLS
Attn: Internet Department
9401 Corporate Lake Drive
Tampa, FL 33634

FAX: 1-813-243-1888

Please include contact information and a copy of your request for quote.

top

Decorative Applications

All wire mesh may not be suitable for decorative applications. Please let us know it’s for a decorative application, so that we can quote the most appropriate wire mesh.

top

Tolerances

Standard tolerances for quantity, shearing, circle shearing, and squareness. Apply to stock items and on special order items for which tolerances are not specified. If you require other than standard tolerances, or tolerances that not listed above, please specify using the welded wire mesh quote form and put the required tolerances in the “Comments Box.”

top

Item

Description

Qty

3629250041

Compare

McNICHOLS Quality Square Welded Wire Mesh, Plain Steel Cold Rolled, 3" Square Opening, 0.2500" Wire Diameter, Welded Untrimmed, 85% Open Area, Sheet, 48.0000" x 120.0000"
Add to cart to see price. Click here to cut this item to size

3693250041

Compare

McNICHOLS Quality Square Welded Wire Mesh, Plain Steel Cold Rolled, 2" Square Opening, 0.2500" Wire Diameter, Welded Untrimmed, 77% Open Area, Sheet, 48.0000" x 120.0000"
Add to cart to see price. Click here to cut this item to size

3693250051

Compare

McNICHOLS Quality Square Welded Wire Mesh, Plain Steel Cold Rolled, 2" Square Opening, 0.2500" Wire Diameter, Welded Untrimmed, 77% Open Area, Sheet, 60.0000" x 120.0000"
Add to cart to see price. Click here to cut this item to size

3102120041

Compare

McNICHOLS Quality Square Welded Wire Mesh, Stainless Steel Type 316, 2" Square Opening, 0.1200" Wire Diameter, Welded Untrimmed, 89% Open Area, Sheet, 48.0000" x 120.0000"
Add to cart to see price. Click here to cut this item to size

3804260041

Compare

McNICHOLS Quality Square Welded Wire Mesh, Stainless Steel Type 304, 4" Square Opening, 0.2500" Wire Diameter, Welded Untrimmed, 89% Open Area, Sheet, 48.0000" x 120.0000"
Add to cart to see price. Click here to cut this item to size

3803260041

Compare

McNICHOLS Quality Square Welded Wire Mesh, Stainless Steel Type 304, 3" Square Opening, 0.2500" Wire Diameter, Welded Untrimmed, 85% Open Area, Sheet, 48.0000" x 120.0000"
Add to cart to see price. Click here to cut this item to size

3802180041

Compare

McNICHOLS Quality Square Welded Wire Mesh, Stainless Steel Type 304, 2" Square Opening, 0.1880" Wire Diameter, Welded Untrimmed, 84% Open Area, Sheet, 48.0000" x 120.0000"
Add to cart to see price. Click here to cut this item to size

3815250048

Compare

McNICHOLS Quality Square Welded Wire Mesh, Stainless Steel Type 304, 1-1/2" Square Opening, 0.2500" Wire Diameter, Welded Untrimmed, 73% Open Area, Sheet, 48.0000" x 96.0000"
Add to cart to see price. Click here to cut this item to size

3801120041

Compare

McNICHOLS Quality Square Welded Wire Mesh, Stainless Steel Type 304, 1" Square Opening, 0.1200" Wire Diameter, Welded Untrimmed, 80% Open Area, Sheet, 48.0000" x 120.0000"
Add to cart to see price. Click here to cut this item to size

McNICHOLS® Quality Wire Mesh - Square Opening Products